If you need to know the electrical requirements for your inground pool, here is a list of common pool equipment and the approximate volts and amps required for each: Pool Pump: 240v, 10amps. Salt Water Chlorinator: 240v, approx 5-8 amps. Pool Heat Pump: 240v, 50 amps.
What kind of outlet do you need for a pool?
Receptacles for pumps and motors must be located between 6 and 10 feet from the pool walls, and they must be GFCI-protected and locked. Outlet receptacles for general use can be no closer than 20 feet from a pool or in-ground spa if they are not GFCI-protected, and no closer than 6 feet away if they are GFCI protected.
How do I run electricity to my pool?
Plug in the pool pump and cover it with a weatherproof cover. With the main service off to the house, wire in GFCI circuit breakers to the electrical panel. Connect an 8-gauge wire to the metal posts of the pool, the pump, and the metal plate on the skimmer and then wire that to the pump to bond the entire pool.
How much does it cost to install electrical for a pool?
Electricians charge $500.00 – $1500.00 to wire up an above-ground pool. Included in the cost should be all supplies. You will need an 18-inch deep trench to run the service from the breaker-box to the pool area.
Do I need an electrician to install a pool?
Generally you do not need an electrician to install an above ground pool. Most above ground pool companies will just install the pool for you and plug the pump in. There’s no need to make it more difficult than it has to be. This will result in usually a 50 or 60 amp feed for a pool power.
Does a pool pump need an outlet?
Consequently, in-ground pool pumps require 240 volts. You won’t be able to plug them into any old outlet on the inside or outside of your house. Above ground pool pumps, on the other hand, run on 120 volts. This means they could be plugged into a regular electrical outlet.
Do you need an electrician to install an above ground pool?
Pool pumps, which pump the water from the pool through the filter, use a lot of electricity, and that often requires the installation of a dedicated circuit. … When you are preparing your above-ground pool installation, we recommend bringing in the assistance of a certified electrician.
What Electrical is needed for above ground pool?
A typical above ground pool pump will require a 20-amp breaker and use #12 gauge wire to deliver the electricity.
Can I use an extension cord for my pool pump?
It’s highly recommended never to use an extension cord to power a pump of an above ground swimming pool. … A pool pump requires a great deal of power and that you can’t provide with a normal extension cord. You’d need one with a #12-gauge wire or a #10-gauge wire.
What does a pool electrician do?
The main job of your electrician is to power and bond the pool and equipment, in accordance with the National Electric Code, article 680 – and, any additional requirements of your local inspector. SUB-PANEL WIRING: A sub-panel is a small breaker box, usually 100 amps, or enough to power all of your pool equipment.
Why do people bond above ground pools?
Why do you have to bond an above ground swimming pool? Bonding your pool is a safety measure to prevent accidentally getting electrocuted or seriously injured. You need to create a field around your swimming pool by attaching the bonding wire to the metal deck, pool equipment, metal pool wall, and even the water.
Can you install a pool yourself?
DIY pool installation is hard work but not difficult; and after the job is complete you can be proud to say you built your own inground pool. All of your family and friends can now enjoy your hard work in the backyard escape you designed and built.
How much does it cost to run an electric above ground pool?
How much does an above ground pool cost to run? It costs about $115 per month to maintain your above ground pool. You can expect to pay an additional $30 to $250 per month on your electric bill to run the pump, filter and heater.
What to do after pool is installed?
What Do You Do After an Above Ground Pool Is Filled With Water?
- Step 1: Learn about how to prevent drowning and pool chemical injuries. …
- Step 2: Turn on the filter. …
- Step 3: Vacuum and skim off debris. …
- Step 4: Test the water, and then test it again. …
- Step 5: Enjoy your pool, but safely!